Water & Sanitation
Water on a project moves through two different worlds, and both are bought here. Underground: potable networks in HDPE PE 100 on 100 and 200 meter coils, sewer collectors in Type B corrugated up to 1325 mm, and perforated drainage that controls the water table on the land itself. Inside the building: pressurized service connections, hot and cold distribution, and the drain system with its vent lines.
It is the same job seen by two buyers — the contractor or the municipality on one side, the hardware distributor or installer on the other. Each card goes to its full spec page.
Water and sanitation products
HDPE PE 100 Water Pipe
PE 100 · 20 – 110 mm · 0.63 – 2.5 MPa
High-density polyethylene for potable water mains and service lines, in coils of 100 and 200 m.
View product
Corrugated Sewer Pipe (Type B)
NTE INEN 2059 · 110 – 1325 mm · 6 m
Double-wall corrugated PVC for municipal sewer mains. Twice the ring stiffness of solid-wall drain pipe, 50-year design life.
View product
PVC Drain and Vent Pipe
NTE INEN 1374 / 2474 · 50 – 200 mm
Sanitary drain and vent pipe with a full spigot-bell fittings catalog — traps, yees, grates, and cleanout adapters.
View product
PVC Threaded Pressure Pipe
1/2" – 2" · 420 – 200 PSI · 6 m
Threaded-joint PVC for potable water service connections at high pressure. 420 PSI at 1/2" down to 200 PSI at 2".
View product
PP-R Thermofusion Pipe
ISO 15874-2 · PN 20 / PN 25 · 20 – 160 mm
Random polypropylene for hot and cold water, heat-fused joints with no glue, in the green and blue lines.
View product
PVC SCH 40 Pipe and Fittings
ASTM D1785 · 1/2" – 6"
Pressure pipe and injection-molded fittings for cold-water lines, 600–180 PSI, with a full fittings catalog.
View product
Subsurface Drainage Pipe
DIN 4262-1 · 110 / 160 / 200 mm · coils
Perforated corrugated PVC that controls the water table in any soil type. Buries deeper than 2.5 m, resists agrochemicals.
View product
Polyethylene Hose (LDPE)
NTE INEN 1744 · 16 – 63 mm · 1/2" – 2"
Black LDPE hose in metric and inch sizes for general-purpose and irrigation runs, 36 to 125 PSI.
View product
PP Threaded Pipe
ISO 13478-2 · 1/2" – 1" · 6 m
Virgin polypropylene for hot and cold service lines. Threaded joints, 100% injection-molded fittings, no solvent cement.
View productHow this work gets bought
Stiffness and standard, in writing
Type B corrugated is specified by ring stiffness — 8 kPa at 110 and 125 mm, 4 kPa from 160 mm up under NTE INEN 2059, with ISO 9969, DIN 16961, and ASTM D2412 equivalents. HDPE goes by PE 100 grade and pressure in MPa. Send the tender spec and we answer against it.
Fewer joints underground
HDPE ships in 100 and 200 meter coils and drainage in 25, 50, and 100 meter coils. Every joint that does not exist is a leak that cannot happen, and on buried work that is the arithmetic that matters.
See HDPE pipeLarge diameters on order
Corrugated runs to 975 mm in normal production; 1065 to 1325 mm is made by agreement between plant and buyer. If the project calls for those diameters, it gets planned around production time, not warehouse stock.
Request a Wholesale Quote
Tell us what you need. We come back with a firm quote with incoterms — the team that builds it is the same team that answers your questions.